Forward Base: Habitat 5 WiP Part 4 "The Ramps"

Today we move beyond the Rough Guide, add the ramps, and begin sorting the left over parts to see where to go next.

First up... I somehow missed installing this workbench which is clearly shown in the drawings of the rough guide. It went in without a hitch but, due to the nature of MDF, there was a risk that the back right corner would separate and tent up. To reduce the risk of that I used a chopstick to press the corner down.

Beyond the Rough Guide...

This is a first gen Kickstarter version of this building and the Rough Guide doesn't address any of the optional resin components.

I assembled and painted the garage door frames and then glued the resin garage doors to their MDF counterpart to get door textures on both sides of the piece in the same way that I did the vent covers in the walls. Unlike the vent resins, which are slightly larger then the MDF they replace, the Garage Door resin is slightly smaller than the MDF it replaces. This will be tricksey later...

The resin frames don't precisely conform to the opening so I used a Sharpie to blacken round the edges. These small spaces will be recessed once the resin is on and won't be visible. More importantly I intend to use this lip to let the garage door sit in the right position when the doors are "closed".

Above the door here you can see one of the resin Vents. Because the resin is larger than the cut-out it sits very nicely and self levels once the MDF vent is glued behind it. 

Time for more adventures with clamps, blue tape, and Super Phatic glue!

At this point I realized that the Garage Doors were going to be reluctant to sit in the door frames resin side out. The largest part of the door is smaller than the opening and the locker wall just inside the door prevents clean access to the inside lip.  I can magnetize the doors, and will probably have to anyway, so they don't fall over when bumped or jostled, but the doors sit very well in the reverse orientation.

 Onward to the Ramps!

The habitat 5 ramp instructions are pretty clear and easy to follow for building the hinges. The hinges were constructed and here you see the top and bottom view of the ramps.

As always I'll go back at the end and dress up the scuffs from where the MDF parts were removed from their frame. Reaper "Nut Brown" is almost a perfect match to the seared brown edges.

I stood the building on end to line up the ramps the way I wanted and glued the hinges on. The ramps work as designed although I'm gonna have to dirty up the underside... not that the building should be deployed with the ramps in the upright position but... ya never know!

 Extra resin bits...

There are a couple of power supply panels that attach to the outside of the building, three fan covers, two vid screen frames, six light fixtures (I actually need seven but one seems to have escaped during the long Winter pause so I may need to fabricate on from the MDF Frame debris pile)

...and then came the five angular pod things... these took a minute to figure out but once I got looking at the spare MDF pile and how the ladders must attach to the building it became clear that these are Feet to support the building above ground level. Its interesting because these are optional resin bits but the ladders require the building to be elevated or the ladders would have to be cut down to fit.

Not shown are a handful of small resin vent covers that I ended up putting in the spare parts bin because the interior etched areas that they cover were not perforated like the main vents. I ended up wanting to keep the interior vent details all MDF and painted similarly. These covers won't go to waste though! Its always handy to have a few extra bits like those.

Next up... finish painting these extra resins and sort out the remaining MDF installation that wasn't covered in the Rough Guide. This is mostly exterior ladders and interior catwalks. I seem to be missing the steps for the catwalk access so I'll have to take another look round to see if they wandered off during he extended time this sat on my desk. At any rate I think general construction should be finished in one more session and then any additional weathering or detailing will be tackled. There is one spot on the outside of the building that just looks unfinished so I'll have to do something to dress that up.

Back to the desk!

Reaper Fantasy Scenics Ritual Circle and Statue

Reaper Bones 4 has a Fantasy Scenics segment that I'm working my way through.  Today I've got the Ritual Circle and The Statue.. which also includes a small ruined temple.

For the Ritual Circle I thought I'd go more towards a horizontal Stargate or Portal since more of my scenarios would find that useful. Transiting models can stand right on it.

First its a black Primer coat then the red lettering with Blood Red (Reaper (R)) and a Drybrush to Highlight the edges of the lettering with Fiery Orange (R).

A quick Drybrush of the whole model follows moving through Cloudy Gray (R), Sky Gray (R) and Solid White (R).

Then the Washes. Blue (Secret Weapon (SW)) in the circle center and inner Surface of the Arc Structures then Sapphire around the outer edge of the circle and on the outer side and crevices of the Arc Structures. The coverage of these was intentionally uneven and the edges blended. Once completely dry Solid White (R) was dry brushed near the cracked details and to create some sense of motion across the main circle. The edges of detail on the Arc Structures were treated the same way.

The sandy earth areas were washed with Flesh (SW) and Dry Brushed with Sunny Skin Tone (Vallejo (V)).

For scale you can see a WiP Wood Elf from Atlantis Miniatures.

The Statue and Temple were treated similarly to the Ritual Circle but use a lot more colors. The floors got some of the same Flesh (SW) as a glaze in places to show the effects of traffic and time.

The Pillars have glazes of Blood Red (SW) and Green (SW) and are re dry brushed with Solid White (R) in an effort to represent some of the more complex Marbles and other stone types used in temple construction.

The Statue itself got a wash of Blood Red (SW) and The Robe of Verdigris Light Green (SW) before getting a final dry brush of Solid White (R).

Both of these models are intended as regular to heavy use game scenery so I avoided putting in details like weeds and leaf accumulations in favor of simple and durable in hopes that they wear better.

Our Atlantis Miniatures Wood Elf WiP has returned to provide scale.

Speaking of the Wood Elves. Here is a WiP shot taken just after the red lettering was started on the Ritual Circle.

These have had color blocks and shading done but not yet highlights or fine detail. I'm using a lot of blue and purple to shade to give some verve to the green base color. I'm painting the bases at the same time as the model to see if that helps to get a camouflaged feel but maintain enough separation to keep them from actually disappearing into the base. Early days on these.
 

Atlantis Miniatures Wood Elves WiP

 

I'm really excited about these Wood Elf minis from Atlantis Minatures. They are part of a Kickstarter fullfillment so might not be up in the shop yet but they historically move pretty quickly from Kickstarter to regular product.  Very nice and kinda rare!

The models came with an assortment of bases. Some are fully detailed resin some are beveled plastic rounds. There was a good supply of basing bling to add details like forest critters, mushrooms, vines, big stones, and the like. This really inspired me to dive into the greenstuff and get to sculpting!

There are four different types of mounts in the set. A giant elk for the Male Warlord, a big panther for the Female Warlord, large Stags, and smaller Deer.

There are male and female versions of all the elves so this will make for a very thematic, and very scary, wood elf Kinband Warparty. You'll be seeing more of these soon but I wanted to say these are not your kinder, gentler type of "Wood Elf"... they are more like "Feral Elf"... many have horns themselves... they look like the sort of merciless forest guardians that might even eat any trespassers they find! They are gonna be fun! 

Forward Base: Habitat 5 WiP part 3

 

A quickie today as the resin/MDF hybrid vents get installed en masse.

Lots of clamps!

I think there were 9 small vents and 8 Large ones.

These were fussy to paint even though the scheme is simple.

The end result however was very cool.  The vents show well on both sides and the final glue up went without a hitch.  In the bottom picture the MDF inside vents are visible as well as the resin outer pieces.

The important part is to assemble the vents so that the smaller MDF portion is precisely centered on the larger resin bit and the overhang is even all the way round.  This has the effect of lining everything up nicely with no adjustment required during the clamping.

The White Formula is: Graveyard Bone (Reaper (R)) x2 over Black Primer, Dry-Brush Splintered Bone (R) edge with Storm Shadow wash (Secret Weapon) wash interior areas of vent grilles with Storm Shadow on both large and small vents.

Next up for Hab 5 are the ramps to the vehicle doors and the resin upgrades to that same area.  After the ramps we'll be moving beyond the "Rough Guide" to do the remaining interior details, access ladders, additional air handlers, figure out what to do about the area around the side door that looks unfinished and out of place... and finally... add the acrylic light fixtures to the outside.  That should finish the build except for any weathering that I decide to do later.  That will be done as a batch of buildings to help me keep the effects consistent. 

Mixed Stone Ruin Process

 After working for a long time in the Greystone Village format I started thinking that I needed some other complimentary stone colors to liven the place up!

This is a step by step of the process used to get to the end state you see on the left.  

This is a very fast process but gave a solid result.

The model is a ruined doorway from the Reaper Bones 4 Kickstarter Fantasy Scenics set.

I undercoated this with Krylon Camo Brown paint/primer.

Picked out some areas of color with 4 basic colors.

Stormy Grey (Reaper(R)), Grey Mist (R), Handle Wood (R), and Krylon Camo Brown. (This is the undercoat color and was not re-applied... just left "bare")

 Stormy Grey is a very dark grey, Grey Mist is a lighter grey with a fair bit of blue added. Handle Wood is a very light brown that is almost tan and the Krylon Camo Brown is a very dark bark brown.

Base coats of the greys were brushed on damp while the handle wood was wet stippled on to give the uneven coverage an irregular rocky texture instead of weak brush strokes.

First highlight layer:

Sky Gray (R) Drybrush over all grays.

Sunny Skin Tone (Vallejo (V)) Drybrush over all browns except the "ground" part of the base.

This starts tying the different colors together so they will look like they've been standing in a pile together for a long time.  The underlying color differences are reduced a little but still have a variegated appearance.

Lining:

Sewer Water Wash (Secret Weapon (SW))

Line all rocks and cracks edge the divots. This is fast and easy and uses a mid size brush with a decent tip just wipe off any excess that looks like a brush stroke.

Damp brush Saddle Brown (R) over the "Ground"

Of course more could be done with the ground but this is a generic game piece that to look at home in a dungeon, a jungle, or in the frozen wilds so it remains neutral here.

Final Step before sealer!

Lightly drybrush the whole model with Splintered Bone (R) focus a little extra coverage on the tops, edges, and broken stone to make them pop.

Splintered Bone is a bright off-white color.

Reaper Dwarf for scale.

Forward Base: Habitat 5 WiP part 2

Today sees the construction of the main structure. But first a little more painting of panels and resin bits.

A few of the vent panels were not laser cut so were painted in while painting the punched out vents and their resin replacements/additions. All the vents, windows, doors, etc. were punched out prior to assembling anything and dry fitted to see if they could be easily installed after assembly. This turned out to be true for the vents and garage bay doors but not for the acrylic windows and doors which fit very tightly and were installed prior to general construction.

The MDF vents were glued to the resin parts and painted both sides. You can see the left side are the painted MDF and the right are the painted resin. The white is Graveyard Bone (Reaper(R)) and Splintered Bone (R) over black primer on the resin and clear sealer on the MDF.  On the MDF side the vent cavities are Glowing Mist (R). For the resin Cavities Soft Body Black (Secret Weapon( SW)) wash to clean up the dry brush bleed.

On the interior rear wall of the building the rollup doors for the toolboxes got a thinned  Phoenix Red (R) and the clear acrylic door was placed.  

 This was a tight fit and, in retrospect, I might have positioned it a little differently because this wall gets doubled by the outside wall which leaves this door recessed vis-à-vis the outer wall. Its not a big deal just something to add to my lessons learned when doing future builds.

Now construction can commence in earnest!

Before attempting to slot things together I carefully trim one side of the coating off the tiny tabs.  This coating helps give these kits a smooth finish but it often seems to bunch up when going into slots and the excess has to be cut away afterwards. Cutting off just one side retains the strengthening effect of the coating while reducing the bunching and occurrence of too tight fits to practically zero.

"The Rough Guide to building habitat 5" on the Antenocitis Workshop site notes that this kit is a little complicated and should be approached in a certain way. Believe it!

The first assembly is the Lattice with Beam, Support Struts, Top Side Panels and Roof Guides for the rear part of the building.

 True to its name the guide is a little quirky. As is the usual case with these kits all of the components of the model have very specific names but the parts are not labeled so have to be carefully selected and test fitting is essential. Some of the parts have names that imply the existence of other parts for example "Beam 1" seems to be the only part named "Beam" in the kit so I spent some extra time trying to located the other "Beams" to make sure the one I had selected was actually "Beam 1"

Next up come the first aid stations.  Volgren Troller has very generously supplied a full First Aid Station and sink for each vehicle bay. The Rough Guide was a little fuzzy here. It details about half of building the most complicated side without mentioning the small positional markings on the struts or how the First Aid stations are constructed... and do the same for the other side... which I mistook for a comment about installing the other side wall when it really specifically was referring to the First Aid Stations.  The kit is very well designed so once I started dry fits it became immediately obvious how things were meant to go.

The inner framework, complete with matching First Aid Stations and side catwalks. The catwalks are not only great places for miniatures to lurk but help a lot with giving the tool boxes and other etched features an illusion of depth.

Now comes the Interior Rear Wall.  Once this wall is in position the whole framework can be slotted into the floor.

Floor installed. For as many slots as the floor part has this went together very easily.  The precision of the laser cutting is really great. The Rough Guide helpfully mentions that the floor should be worked starting from the rear wall. The front wall is not yet on and the side walls are still a bit flexible at this point making them a lot easier to deal with in the fitting.

Time for the Front Wall.  This slots into the floor and relies on the flexibility of the Top Side Panels to be lifted enough to get the wall into position.

Next comes the Exterior Rear Wall which completes the main structure.  There ae still a lot of things remaining to do but this was the tricky bit.

Remember those resin vent panels? Add them in here as they get painted. The printed side is reversed to show the etched detail on the other side of the wall panel and the slightly larger resin side allows for the whole thing to be glued in flush.

First picture shows the resin side.

Second picture shows the painted MDF side.

These slide in very easily and add some extra detail. 

Back to the desk to work on the ramps, doors, ladders, interior details etc...

 

Forward Base: Habitat 5 - The Workshop WiP

Forward Base: Habitat 5 - The Workshop

Habitat 5 is a workshop with two vehicle bays that should be an early structure for a new outpost.

The kit is from the Forward Base Kickstarter by Antenocitis' Workshop and this one includes the resin upgrade as well as the other additional rewards from that campaign.

I sprayed all the MDF with a dead-flat sealer and began painting the details.  These kits are pre-painted which does not mean that no painting needs to be done but rather that they have a single color per sheet paintable coating which allows for the painted surface to look a lot less like painted MDF.

You can see here the ramps are on a yellow colored sheet and I've painted in details like safety markings, logos, tools, etc... The floors and walls are grey and roof panels white. 

These are weathered panels which means the laser cutter was turned up to do some light scorching. It makes for a nice effect on the large areas that I leave unpainted like the grey floor of the vehicle bays.

I still have tool boxes and some cabinets to paint in before assembly.

Then came cleaning and priming the resin components and familiarizing myself with the types of parts that might be included. I learned from some earlier builds that the resin parts need to be considered from the very beginning as they sometimes completely replace structures early in the build process.

For vents and doors the MDF is pre-cut so the etched part can be removed and replaced with a resin upgrade. I have removed the parts to be replaced, turned them round, and glued them to the back side of the resin replacements. Now I'm in the process of painting both sides. In this way I get detailed vents and garage doors on both sides.

 

More on Hab 5 next installment... I also got a little work done on the body bags and am starting the ice vending machines and porta-loos for the Post Apocalypse table.

Last, but far from least, The massive Etherfields boardgame arrived just as I was coming up to post!

With a 17.5 kg mailing weight this thing is a real beast.  I'll be taking a look inside after my wife gets home so she can enjoy it too.

Cheers